دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Modification of PES-based nanofiltration membranes by addition of sodium citrate surfactant modified- iron oxide nanoparticlesاصلاح غشاهای نانوفیلتراسیون بر پایه پلیاترسولفون PES توسط افزودن نانوذرات اکسید آهن اصلاح شده با سورفاکتانت سدیمسیترات117265710.22103/jsse.2020.2657FAسارامرادیگروه مهندسی شیمی، دانشکده فنی مهندسی، دانشگاه اراک، ایرانعبدالرضامقدسیگروه مهندسی شیمی، دانشکده فنی مهندسی، دانشگاه اراک، ایرانسمانهبنده علیگروه مهندسی شیمی، دانشکده فنی مهندسی، دانشگاه اراک، ایرانJournal Article20200225The use of nanofiltration membranes has been attractive in many fields especially in water treatment due to high separation performance. The most used membranes are polymeric. However, the achievement of high mechanical stability and good separation performance is one of the important challenges for the application with various operating conditions.<br /> In this study, PES-based nanofiltration membranes were fabricated by the phase inversion method. The Fe3O4 nanoparticles with the concentration of 0.5 wt.% and different concentrations of sodium citrate were used in the membrane preparation. The FTIR analysis was used to investigate the formation of chemical bonding. Moreover, membrane morphology and surface topography were studied by FESEM and AFM analysis, respectively. The separation performance of membranes was examined by the contact angle, membrane porosity, water content, pure water flux (PWF), and salt rejection. The results showed the highest PWF (47 L/m2h) and salt rejection (68%) for M5 at 0.5 wt.% of iron oxide nanoparticles and 0.3 wt.% of sodium citrate. However, Na2SO4 rejection increased slightly compared with the pristine PES membrane (about 11%). But the PWF improved about 66% compared with the pristine PES membrane due to increase membrane hydrophilicity and better dispersion of Fe3O4 nanoparticles and the formation of more active sites for Na2SO4 adsorption. The good dispersion of nanomaterials led to reducing membrane roughness, and also the increase of hydrophilic groups led to improve antifouling properties of prepared membranes.استفاده از غشاهای نانوفیلتراسیون در تصفیهی آب به دلیل عملکرد بالای جداسازی مورد توجه بوده است. اکثر غشاهای مورد استفاده در این زمینه پلیمری هستند. هرچند که دستیابی به مقاومت مکانیکی بالا و عملکرد جداسازی مناسب از جمله چالشها برای استفاده از آنها در شرایط عملیاتی مختلف است. در این تحقیق، غشاهای نانوفیلتراسیون بر پایه پلیاترسولفون با استفاده از روش وارونگی فاز ساخته شدند. در ساخت غشاها از نانوذرات اکسید آهن (Fe3O4) با غلظت 5/0 درصد وزنی و غلظتهای مختلف از سدیم سیترات استفاده شد. جهت بررسی تشکیل پیوندهای شیمیایی مورد نظر از آنالیز طیف سنجی تبدیل فوریه مادون قرمز استفاده شد. همچنین مورفولوژی و توپوگرافی سطحی غشاها به ترتیب توسط تصاویر میکروسکوپ الکترونی روبشی نشر میدانی و میکروسکوپ نیروی اتمی بررسی شدند. عملکرد جداسازی غشاها توسط آزمایشهای زاویه تماس، اندازهگیری تخلخل، محتوای آب، شار آب خالص و همچنین پسدهی نمک مورد ارزیابی قرار گرفت. <br /> نتایج، بالاترین شار آب خالص ( L/m2h 47) و پسدهی نمک (68%) را در غشای محتوی 5/0 درصد وزنی نانوذره اکسید آهن و 3/0 درصد وزنی سدیم سیترات نشان داد. اگرچه پسدهی نمک در مقایسه با غشای خالص پلی اتر سولفون افزایش کمی پیدا کرد (حدود 11%). اما شار آب خالص به میزان 66% نسبت به غشای پلیاترسولفون خالص بهبود پیدا کرد به دلیل افزایش آبدوستی غشا و پخش شدن بهتر نانوذرات اکسید آهن و همچنین افزایش سایتهای فعال جذب نمک Na2SO4. پخش شدن همگن نانوذرات اکسید آهن باعث کاهش زبری سطح و همچنین افزایش گروههای آبدوست موجب بهبود خواص ضدگرفتگی غشاها شده است.دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Experimental Study and Thermodynamic Modeling of Separation of Toluene from Heptane by a Deep Eutectic Solventمطالعه تجربی و مدل سازی ترمودینامیکی جداسازی تولوئن از هپتان به کمک حلال های نقطه اتکتیک عمیق1830268710.22103/jsse.2020.2687FAحامدصداقت زادگان اصفهانی1. دانشکده مهندسی شیمی، دانشگاه صنعتی امیرکبیر (پلی تکنیک تهران)، تهران، ایرانعلیخوش سیما2. دانشکده مهندسی شیمی و نفت، دانشگاه حکیم سبزواری، سبزوار، تهرانغلامرضاپازوکیدانشکده مهندسی شیمی، دانشگاه صنعتی امیرکبیر (پلیتکنیک تهران)، تهران، ایرانJournal Article20200425Azeotropic point is one of the most important limitations in petrochemical units that prevents the separation and purification of various materials and products. In this study, deep eutectic solvents were used as the brittle azeotrope breaker for a mixture of heptane and toluene. Recently, low eutectic solvents have become increasingly popular as environmentally friendly green solvents to replace volatile organic compounds (VOCs). These solvents consist of a combination of a hydrogen bond acceptor (such as choline chloride) and a hydrogen bond donor (such as urea, thiourea, and 1,2-propandiol). In this study, the deep eutectic solvents were synthesized with a ratio of 1:3 for choline chloride and thiourea as solvent number one, and a ratio of 1:2 for choline chloride and 1,2-propandiol as solvent number two, respectively. The separation process was performed at 298.15 K and atmospheric pressure. The predictive UNIFAC model, was used to model the mentioned systems. The mean deviation (RMSD) for the first and second systems were calculated to be 3.38 and 2.99, respectively.نقطه آزئوتروپ یکی از مهمترین محدودیتهای موجود در واحدهای پتروشیمی میباشد که مانع جداسازی و خالص سازی مواد و محصولات مختلف می شود. در این پژوهش از حلال اتکتیک عمیق به عنوان شکننده نقطه آزئوتروپ مخلوط هپتان و تولوئن استفاده شده است. اخیراً حلال های اتکتیک عمیق به عنوان حلال های سبز سازگار با محیط زیست مورد توجه بیشتری واقع شده اند تا بتوانند جایگزین ترکیبات آلی فرار شوند. این حلالها از ترکیب یک پذیرنده پیوند هیدروژنی و یک دهنده پیوند هیدوژنی تشکیل شده اند. در این پژوهش، حلالها به ترتیب با نسبت 3:1 برای کولین کلراید و تیواوره تحت عنوان حلال شماره یک، و نسبت 2:1 برای کولین کلراید و 1و2-پروپاندیول تحت عنوان حلال شماره دو ساخته شده اند. به فرآیند جداسازی در دمای 15/298 کلوین و فشار اتمسفریک انجام شده است. همچنین به کمک مدل ترمودینامیکی UNIFAC که یک مدل پیشگو است برای مدلسازی سیستم مایع - مایع سه جزئی فوق استفاده شده است. انحراف میانگین (RMSD) برای سیستم اول و دوم به ترتیب 38/3 و 99/2 محاسبه شده است.دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Fabrication and Characterization of electerospun nanocomposite based on Acrylic /Halloysite nanotubes for fibrous filter mediaتهیه و مشخصهیابی نانوکامپوزیت الکتروریسی پلی اکریلونیتریل/نانولوله هالوزیت در بستر فیلتر لیفی3142274310.22103/jsse.2020.2743FAعرفانصدیقی مشتقینگروه شیمی و علوم الیاف، دانشکده مهندسی نساجی، دانشگاه امیر کبیر، تهرانمحمدحسنکنعانی جزیگروه شیمی و علوم الیاف، دانشکده مهندسی نساجی؛ دانشگاه صنعتی امیرکبیرسمیهاکبریگروه شیمی نساجی و علوم الیاف، دانشکده مهندسی نساجی، دانشگاه امیر کبیر، تهران، ایرانJournal Article20200204Separation of airborne pollutants such as dust, bacteria, and viruses play an important role in humanitarian health. In this field, acrylic polymer with many properties such as electrospinning capability, thermal resistance, and high chemical resistance is attracting scientific and commercial interests as an active layer for fibrous filter media. The aim of this paper is to utilize low cost, natural resource, biocompatible, and high mechanical strength Halloysite nanotubes (HNTs) for improving filtration efficiency. In this regard, acrylic polymer nanofibers were fabricated by solution electrospinning method on nonwoven support with and without HNTs to fabricate nanocomposite and acrylic membrane. The structure and morphology of membranes were examined by Fourier-transform infrared spectroscopy (FTIR), electron scanning electron microscopy (SEM), and Energy-dispersive X-ray spectroscopy (EDX). Furthermore, the mechanical properties of the samples were analyzed using a single-axis tensile test. Finally, in order to evaluate the filtration efficiency measurement, DOP (dispersed oil particle) were utilized. The results reveal that the nanocomposite membrane has a better performance comparing to the acrylic membrane due to the separation of 95.5% of DOP particles. This layer could be applied as an active layer in N95 face mask.جداسازی آلایندههای موجود در هوا، نظیر انواع ریزگرد، باکتری و ویروس، نقش مهمی در سلامت انسان دارد. دراینزمینه پلیمراکریلیکی با ویژگیهای مطلوب فراوان مانند قابلیتِ الکتروریسی، مقاومت حرارتی و مقاومت شیمیایی بالا ازنظر تجاری و علمی بهعنوان لایه مؤثر در بستر فیلتر لیفی استفاده میشود. در این مقاله از نانولولههای هالوزیت، بهعنوان مادهی ارزان و زیستسازگار، بهمنظور بهبود بهرهوری فیلتراسیون در لایه فعال استفاده شد و دو نمونه غشای پلیمراکریلیکی و غشای نانوکامپوزیتی حاوی نانولولههای هالوزیت به روش الکتروریسی بر روی بستر بیبافت تهیه شد و برای بررسی ساختار و شکلشناسی نمونههای نانو الیافِ تولیدشده، آزمونهای طیفسنجی مادونقرمز (FTIR)، میکروسکوپ الکترونی روبشی (SEM) و طیفسنجی پراش انرژی پرتوایکس (EDX) بهکار گرفته شدند. استحکام کششی نمونهها با استفاده از آزمون کششی تکمحور بررسی شد. درنهایت، بهمنظور بررسی سنجش بهرهوری فیلتراسیون، از آزمون دیسپرس ذرات دیاکتیلفتالات (DOP) بهره بردیم. مشاهده شد غشای نانوکامپوزیتی، باقابلیت جداسازی %5/95 ذرات ِ DOP، در مقایسه با غشای پلیمراکریلیکی از عملکرد بهتری بهمنظور بهکارگیری در فیلترهای هوا و جداسازی آلایندهها برخوردار است. این لایه می تواند به عنوان لایه فعال در ماسک تنفسی در تولید ماسک N95 باشد.دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Synthesis of nickel-copper-zinc ferrite nanoparticles by sol-gel auto- combustion microwave-assisted method for remove of methylene blue dyeسنتز نانوذرههای فریت نیکل-مس-روی با روش سل-ژل خود احتراقی با کمک امواج مایکرو برای حذف رنگ متیلن آبی4357276410.22103/jsse.2020.2764FAفاطمهمعصومیدانشکده شیمی، دانشگاه علم و صنعت ایران، تهران، ایرانمحبوبهربانیدانشکده شیمی، دانشگاه علم و صنعت ایران، تهران، ایرانJournal Article20200914Ni0.2-xCuxZn0.8Fe2O4 ferrite nanoparticle powders were prepared with special ratios (X = 0, 0.1, 0.2) by automatic sol-gel auto-combustion using microwaves. The resulting powders use X-ray diffraction, scanning electron microscopy, infrared spectroscopy, X-ray energy scattering, diffuse reflection spectroscopy and vibrating sample magnetometer and photocatalytic activity of the samples were analyzed by UV-Vis analysis. The average crystal grain size of magnetic nanoparticles was calculated using half-maximum full-width data (FWHM) and X-ray scattering according to the Dubai-Sherry formula. The results of the X-ray diffraction pattern showed that the obtained ferrite nanoparticles have a single-phase cubic spinel structure and do not have an impure phase. Careful observations through scanning electron microscopy have shown that nickel-zinc-copper ferrite nanoparticles were spherical in shape. From the IR peak of the octagonal and tetrahedral vibrations, the formation of the spinel structure was confirmed. The presence of nickel, copper and zinc elements in ferrite nanoparticles was confirmed by EDX analysis. The peak absorption of ferrite nanoparticles obtained from the diffusion spectrum (DRS) was 310, 438 and 315 nm, respectively. Finally, magnetic measurements show that ferrite nanoparticles are highly saturated with ferromagnetic matter. In following, the photocatalytic and adsorption activity of the samples for removing of methylene blue contaminants with concentration of 5 and 15 mg/mL were investigated in 3 times. It was shown that the ferrite sample containing only nickel had better absorption and destruction of the contaminant than other ferrite samples.در این پژوهش، نانوذرههای فریت Ni0.2-xCuxZn0.8Fe2O4 با نسبتهای مختلف (X= 0, 0.1, 0.2) با روش سل-ژل خود احتراقی به کمک امواج مایکرو تهیه شدند. خصوصیات پودرهای حاصل با استفاده از پراش پرتو ایکس (XRD)، میکروسکوپ الکترونی روبشی (SEM)، طیف سنجی مادون قرمز (IR)، پراکندگی انرژی پرتو ایکس (EDX)، طیف سنجی بازتابی پراکندگی (DRS) و مغناطیس سنج نمونه ارتعاشی (VSM) مورد بررسی قرار گرفت. نتایج حاصل از الگوی پراش پرتو ایکس نشان داد که نانوذرههای فریت به دست آمده دارای ساختار اسپینل مکعبی تک فاز هستند و ناخالصی ندارند. اندازه میانگین دانههای بلوری نانوذرههای مغناطیسی با کمک دادههای نیمه حداکثر از عرض کامل (FWHM) حاصل از پراش اشعه ایکس با توجه به فرمول دبای-شرر محاسبه شد. تصاویر به دست آمده از طریق SEM نشان داد که نانوذرههای فریت نیکل-روی-مس از نظر شکل کروی هستند. از قله IR مربوط به ارتعاشهای هشت وجهی و چهاروجهی، تشکیل ساختار اسپینل تأیید شد. حضور عناصر نیکل، مس و روی در نانوذرههای فریت با آنالیز EDX تأیید شدند. قله جذب نانوذرههای فریت به دست آمده از طیف پراش نور بازتابی (DRS) به ترتیب 310، 438 و 315 نانومتر بودند. سرانجام، اندازهگیریهای مغناطیسی نشان دادند که نمونههای سنتز شده، مادههای فرومغناطیسی با مغناطش اشباع بالا هستند. درنهایت، فعالیت فتوکاتالیزوری و جذب نمونههای سنتز شده برای حذف آلاینده متیلن آبی با غلظت mg/mL 15 و 5 در سه زمان مورد بررسی قرار گرفتند. مشخص شد که نمونه فریتی که تنها حاوی نیکل است، از جذب و تخریب بهتر آلاینده نسبت به نمونه فریتهای دیگر برخوردار بوده است.دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Investigation of the Impact of Salt Water Depth on Stair Solar Desalination Using Comsol Softwareبررسی تاثیر عمق آب شور در آب شیرین کن خورشیدی پلکانی با استفاده از نرم افزار Comsol5870277010.22103/jsse.2021.2770FAفروغدرانیگروه مهندسی شیمی، دانشگاه سیستان و بلوچستان، زاهدان، ایرانسید محمدحسینیگروه مهندسی شیمی، دانشگاه سیستان و بلوچستان، زاهدان، ایرانمحمدرضاسردشتی بیرجندیمهندسی شیمی، دانشکده مهندسی شهید نیکبخت، دانشگاه سیستان و بلوچستان، زاهدان، ایران0000-0002-6555-3365فرهادشهرکیگروه مهندسی شیمی، دانشکده شهید نیکبخت، دانشگاه سیستان و بلوچستان، زاهدان، ایرانJournal Article20200711The growing global population on the one hand, as well as the scarcity of fresh water resources, are the reasons for the global water crisis. Therefore, to cope with these conditions, humans need to find alternative and renewable freshwater sources through the treatment of existing unhealthy waters or desalination of saltwater. Staircase solar water purifiers are among the many devices used in water purification. This paper deals with the simulation of a staircase solar water desalination at the University of Sistan and Baluchestan with Comsol software. After comparing the experimental data and the results of the software, the influence of saline depth parameter on the stairs on the amount of fresh water output from desalination was investigated. For this purpose, the performance of the device for saline water depths of 0.005, 0.0075 and 0.01 m with inlet saline flow rate of 0.2 (kg / min) was investigated. The results show that with increasing salt-water depth, the water temperature decreases and the temperature difference between the water surface and the glass surface decreases and the amount of fresh water produced decreases.آب شیرین کن خورشیدی پلکانی از جمله انواع دستگاههایی است که در زمینه تصفیه آب به کار میروند. در این مقاله به شبیه سازی آب شیرین کن خورشیدی پلکانی موجود در دانشگاه سیستان و بلوچستان با نرم افزار Comsol پرداخته شده است. پس از مقایسه دادههای تجربی و نتایج حاصل از نرم افزار، تاثیر پارامتر عمق آب شور روی پلهها بر میزان تولید آب شیرین خروجی از آب شیرین کن مورد بررسی قرار گرفت. عملکرد دستگاه برای عمقهای آب شور 005/0 و 0075/0 و 01/0 متر با نرخ آب شور ورودی (kg/min) 2/0 مورد بررسی قرار گرفت. نتایج نشان داد که با افزایش عمق آب شور، دمای آب به دست آمده کاهش یافته و همچنین اختلاف دما بین سطح آب و سطح شیشه کاهش مییابد و از میزان آب شیرین تولیدی نیز کاسته میشود.<br /> آب شیرین کن خورشیدی پلکانی از جمله انواع دستگاههایی است که در زمینه تصفیه آب به کار میروند. در این مقاله به شبیه سازی آب شیرین کن خورشیدی پلکانی موجود در دانشگاه سیستان و بلوچستان با نرم افزار Comsol پرداخته شده است. پس از مقایسه دادههای تجربی و نتایج حاصل از نرم افزار، تاثیر پارامتر عمق آب شور روی پلهها بر میزان تولید آب شیرین خروجی از آب شیرین کن مورد بررسی قرار گرفت. عملکرد دستگاه برای عمقهای آب شور 005/0 و 0075/0 و 01/0 متر با نرخ آب شور ورودی (kg/min) 2/0 مورد بررسی قرار گرفت.دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Rapid Synthesis of ZnS-CuS Nanocomposite and its Photocatalytic Application for Methylene Blue Removal from Aqueous Mediaسنتز سریع نانوکامپوزیت سولفید روی-سولفید مس و کاربرد فتوکاتالیستی آن جهت حذف متیلن بلو از محیط آبی7180277110.22103/jsse.2021.2771FAمریمفتح الهبخش مهندسی مواد و متالورژی، دانشگاه شهید باهنر کرمان، ایرانغلامرضاخیاطیبخش مهندسی مواد و متالورژی، دانشگاه شهید باهنر کرمان، ایرانJournal Article20201023A microwave approach is being presented for the synthesis of sulfide nanostructures as well as two component composites between them. ZnS, CuS and heterojunction mixture between the two were obtained using the relative metal acetates and thiourea, i.e., sulfur source in N, N-dimethylformamide (DMF), which was utilized as both solvent and surface binding agent under microwave irradiation for just 20 seconds. The samples were characterized using field-emission scanning electron microscope, energy dispersive X ray, X-ray diffraction and diffuse reflectance spectrophotometry. Photo-degradation of methylene blue as a common pollutant was investigated as an application for the synthesized materials. Removal efficiency of about 60% after 30 minutes of contact in darkness and 60 minutes of illumination using low-power UVB light remained fairly unchanged after 5 running cycles. The obtained composite between ZnS and CuS is a p-n type heterojunction able to show better photocatalytic activity compared to each of the constituting sulfides alone.در این تحقیق به سنتز نانو کامپوزیت های تک جزئی و دوجزئی سولفید مس و سولفید روی پرداخته شده است. در همین راستا برای ایجاد اتصال نامتجانس بین فازهای مذکور در کامپوزیت نهایی، نمک های استات مس و استات روی به عنوان پیش ماده یون فلزی و تیواوره به عنوان منبع سولفور در محیط N، N-دی متیل فرمامید (به عنوان حلال و عامل اتصال سطحی) به مدت 20 ثانیه تحت تابش ماکروویو قرار گرفتند. نمونهها با روشهای میکروسکوپی الکترونی روبشی نشر میدان، طیف سنجی اشعه ایکس بر حسب انرژی، تفرقسنجی اشعه ایکس و طیفسنجی انعکاس نفوذی مشخصهیابی شدند. متیلن بلو به عنوان یک آلاینده با قابلیت ردیابی بالا جهت انجام آزمون فتوکاتالیستی نمونه های سنتز شده مورد استفاده قرار گرفت. نتایج نشان داد که راندمان قابل قبول حذف رنگ حدود 60 درصد بعد از گذشت 5 سیکل کاری شامل 30 دقیقه تماس با محلول رنگی در محیط تاریک و 60 دقیقه تابش دهی با لامپ توان پایین فرابنفش حفظ می شود. همچنین کامپوزیت تولید شده بین سولفید روی و سولفید مس دارای اتصال نامتجانس از نوع p-n بوده و قابلیت تخریب فتوکاتالیستی بهتری نسبت به فازهای سولفیدی مجزا دارد.دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Synthesis of Zeolitic imidazolate framework-8 based magnetic nanocomposite incorporated with silver nanoparticles for efficient removal of organic pollutants from wastewaterسنتز نانوکامپوزیت مغناطیسی بر پایه چارچوب ایمیدازول زئولیتی-8 آلاییده شده با نانوذرات نقره به منظور حذف مؤثر آلاینده آلی از پساب8193277210.22103/jsse.2021.2772FAجعفرعبدیگروه مهندسی شیمی-دانشکده مهندسی شیمی و مواد- دانشگاه صنعتی شاهرودJournal Article20201105Metal–organic frameworks (MOFs) are a new class of coordination polymers and porous materials which have a wide application in various scientific fields based on their dual structures. In this work, synthesis of γ-Fe2O3@SiO2@ZIF-8 magnetic nanocomposite for removal of organic pollutant from wastewater was studied. Then, for improving photocatalytic performance of this compound, silver nanoparticles were added into the ZIF-8 framework using photo-deposition method. Synthesized nanostructures were characterized using different structural analysis such as XRD, SEM/EDX, FTIR, ICP-OES and VSM. Next, the photodegradation performance of the prepared materials for removal of Rhodamine B were investigated by studying the effects of several parameters including photo-catalyst dosage, initial dye concentration and solution pH. The results showed that γ-Fe2O3@SiO2@ZIF-8-Ag photo-catalyst with the efficiency of 96% had the best performance in degradation of organic dye. Also, the stability tests showed that the synthesized photo-catalyst can maintain its appropriate activity after five cycles. Therefore, the proposed nanocomposite in this work seems to be a reusable and economical photocatalyst for water purification.چارچوبهای آلی-فلزی کلاس جدیدی از پلیمرهای کئوردینه شده و مواد متخلخل هستند که به دلیل بهرهمندی از ساختار دوگانه، در زمینههای مختلف علمی کاربرد گستردهای دارند. در این پژوهش سنتز نانوکامپوزیت مغناطیسی γ-Fe2O3@SiO2@ZIF-8 جهت حذف آلاینده آلی از پساب مورد مطالعه قرار گرفته است. در ادامه برای بهبود عملکرد فوتوکاتالیستی این ترکیب، نانوذرات نقره با روش رسوبدهی نوری به ساختمان چارچوب آلی فلزی ZIF-8 افزوده شده است. نانوساختارهای سنتز شده به کمک آنالیزهای ساختاری مختلف از جمله XRD، SEM/EDX، FTIR،ICP-OES و VSM شناسایی شده و عملکرد آنها جهت حذف رنگزای ردامین ب (RhB) با مطالعه اثر پارامترهای مختلف از جمله مقدار دوز فوتوکاتالیست، pH محلول و غلظت اولیه رنگزا مورد بررسی قرار گرفت. نتایج نشان میدهد که فوتوکاتالیست γ-Fe2O3@SiO2@ZIF-8-Ag با بازدهی 96% بهترین عملکرد را در حذف رنگزای آلی داشت. همچنین آزمایشات پایداری نشان داد که فوتوکاتالیست سنتز شده پس از پنج چرخه عملکرد مناسب خود را حفظ می-کند. بنابراین، نانوکامپوزیت پیشنهاد شده میتواند به عنوان فوتوکاتالیست مناسب و مقرون به صرفه با قابلیت استفاده مجدد در زمینه تصفیه آب مورد توجه قرار گیرد.دانشگاه شهید باهنر کرمان و انجمن مهندسی شیمی ایراننشریه علوم و مهندسی جداسازی2008-396312220210120Investigation of photocatalytic performance of ternary nanocomposites (silver/ titanium dioxide nanosheets/reduced graphene oxide) for degradation of tetracycline and modeling the process by ANFISبررسی عملکرد فوتوکاتالیستی نانوکامپوزیت سه تایی ( نقره/ نانوورقههای تیتانیومدیاکسید/گرافناکسید کاهش یافته) به منظور تخریب آنتی بیوتیک تتراسایکلین و مدلسازی فرایند با سیستم استنتاج فازی-عصبی تطبیقی94110277310.22103/jsse.2021.2773FAفاطمه الساداتطباطبایی یزدیدانشکده فنی فومن، پردیس دانشکدههای فنی، دانشگاه تهران، فومن، ایرانآزادهابراهیمیان پیربازاریدانشکده فنی فومن، پردیس دانشکده های فنی دانشگاه تهرانفاطمهاسماعیلی خلیل سراییاستادیار (ریاضی)،
دانشکده فنی فومن،
پردیس دانشکده های فنی،
دانشگاه تهراننداگیلانیدانشکده فنی، دانشگاه گیلان، رشت، ایرانJournal Article20201117In this research, ternary nanocomposites, Ag/rGO-TiO2 (x) were synthesized through the photodeposition of different amounts of silver on titanium dioxide nanosheets (TNs) combined with reduced graphene oxide (rGO (. Different techniques such as XRD, FESEM/EDX, TEM, DRS and Raman spectroscopy were employed for structural and morphological characterization of the synthesized samples. The photocatalytic degradation experiments were carried out in the presence of 75 mg of the prepared samples in 100 mL of the aqueous solution of tetracycline with 30 mg/L concentration under visible light. The best photocatalytic performance was related to the ternary nanocomposite Ag/rGO-TiO2 (0.076) (synthesized in the presence of 0.076 g AgNO3) with the percentage of TC degradation equal to 52.56%, the can be attributed to plasmonic resonance of silver plasmonic nanoparticles. The removal percentage of tetracycline was 37.93% in the exstance of pure titanium dioxide nanosheets (TNs) under the same conditions. Adaptive neuro fuzzy inference system was used for modeling and prediction of the photocatalytic performance of the synthesized ternary nanocomposites.در این تحقیق، نانوکامپوزیتهای سهتایی Ag/rGO-TiO2 (x) از طریق پخش نوری مقادیر مختلف نقره (نانوذرات پلاسمونی) بر روی نانوورقههای تیتانیومدیاکسید (TNs) ترکیب شده با گرافناکسید کاهش یافته (rGO) سنتز شدند. تکنیکهای مختلفی از جمله XRD، FESEM/EDX، TEM، DRS و Raman برای شناسایی ساختاری و مورفولوژیکی نانوکامپوزیتهای سنتز شده به کار گرفته شدند. آزمایشهای تخریب فوتوکاتالیستی تتراسایکلین در حضور 75 میلیگرم از نمونه های سنتز شده در 100 میلی لیتر محلول آبی تتراسایکلین با غلظت 30 میلیگرم بر لیتر تحت نور مرئی انجام شدند. بهترین عملکرد فوتوکاتالیستی مربوط به نانوکامپوزیت سهتایی Ag/rGO-TiO2 (0.076) (سنتز شده در حضور 076/0 گرم نقره نیترات) ، با درصد تخریب 56/52 بود که می توان آن را به رزونانس پلاسمونیک نانوذرات نقره نسبت داد. درصد حذف تتراسایکلین توسط نانوورقههای تیتانیومدیاکسید خالص (TNs) در شرایط مشابه 93/37 درصد بود. به منظور مدلسازی و پیشبینی فعالیت فوتوکاتالیستی نمونههای سهتایی سنتز شده از سیستم استنتاج فازی-عصبی تطبیقی (ANFIS) استفاده شد.