@article { author = {Haji-Savameri, Mohammad and Hemmati-Sarapardeh, Abdolhossein and Norouzi-Apourvari, Saeid and Irannejhad, Ahmad and Ghasemzadeh, Amir and Schaffie, Mahin}, title = {Modeling of Asphaltene Deposition on Coated Metal Surfaces}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {1-14}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2575}, abstract = {Asphaltene deposition is one of the most common problems in the petroleum industry that could be very costly and cause many operational problems. In order to select the optimal operating conditions, deposition kinetics models can be very effective in treatment of asphaltene deposition at the field scale. In this study, asphaltene was first extracted from crude oil by standard methods and then its deposition kinetics on metal surfaces coated by Teflon and silica films was evaluated in both static and dynamic flow states. Investigations showed that the flow state is effective on the asphaltene deposition kinetics so that in the static state the nth-order kinetics model and in the dynamic state the double exponential model are in the best agreement with the experimental data. According to the results, at static state and concentration of 2000 ppm, the RF and SF values for Teflon coating are 78.8023 and 21.1976, respectively, indicating faster fast deposition process for this coating. Whereas for silica film, the RF value is lower than SF, indicating a faster slow deposition process for this coating.}, keywords = {Modeling,Deposition Kinetics,Asphaltene Deposition,Coated Metal Surfaces}, title_fa = {مدل سازی نشست آسفالتین بر روی سطوح فلزی پوشش دار}, abstract_fa = {رسوب آسفالتین یکی از مشکلات مرسوم در صنعت نفت است که رفع آن بسیار هزینه‌بر بوده و مشکلات عملیاتی بسیاری ایجاد می‌کند. با توجه به این مسئله استفاده از مدل‌های سینتیکی، به منظور انتخاب شرایط عملیاتی مطلوب در درمان ‌نشست آسفالتین در مقیاس میدانی می‌تواند بسیار موثر باشد. در این پژوهش ابتدا آسفالتین بر اساس روش‌های استاندارد از نمونه نفت-خام جداسازی شد و سپس سینتیک نشست آن بر سطوح فلزی پوشش‌دار از نوع تفلون و فیلم سیلیکا، در دو حالت جریانی استاتیک و دینامیک ارزیابی شد. بررسی‌ها نشان داد که نوع حالت جریان بر سینتیک نشست آسفالتین موثر است به نحوی که در حالت استاتیک مدل سینتیک مرتبه n ام و در حالت دینامیک مدل سینتیک دو نمایی بهترین تطابق با داده‌های تجربی را دارند. طبق نتایج بدست آمده، در حالت استاتیک و غلظت ppm 2000، مقدار RF و SF برای پوشش تفلون به ترتیب، 8023/78 و 1976/21 می‌باشد که نشان دهنده سریع‌تر بودن فرآیند نشست سریع برای این پوشش می‌باشد در حالیکه برای فیلم سیلیکا مقدار RF کمتر از SF می‌باشد که نشان دهنده سریع‌تر بودن فرآیند نشست آهسته برای این پوشش می‌باشد.}, keywords_fa = {مدل‌سازی,سینتیک جذب,‌نشست آسفالتین,سطوح فلزی پوشش‌دار}, url = {https://jsse.uk.ac.ir/article_2575.html}, eprint = {https://jsse.uk.ac.ir/article_2575_fc99d21813f5320953415be46c1ae55e.pdf} } @article { author = {Shakeri, Mehdi and Iranshahi, Davood}, title = {Modeling and Simulation of Proposed Multifunctional Reactors to Increase the Aromatics Production in the Catalytic Naphtha reforming}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {15-28}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2600}, abstract = {Abstract In this research, improvement of catalytic naphtha reforming as one of the important processes in refineries and petrochemicals industries has been considered. The main focus is on replacing the conventional packed-bed reactors with new multifunctional reactors. These proposed reactors include catalytic naphtha reforming and methaxylene hydrodealkylation processes separated by a solid wall and a sweep gas section separated from naphtha reforming by a Pd-Ag membrane layer. The endothermic naphtha reforming, on the one hand, exchanges heat with the methaxylene hydrodealkylation, while on the other hand, it performs hydrogen exchange by sweep gas section. According to the simulation results, the aromatic production in the proposed system was increased by about 11% compared to conventional reactors. Finally, the effects of operating conditions such as feed temperature of hydrodealkylation process, seep gas inlet pressure on the performance of the system have been studied. Keywords: Catalytic Naphtha Reforming Process, Multifunctional Reactor, Palladium Membrane, Methaxylene Hydrodealkylation Process, Aromatic Production}, keywords = {Catalytic Naphtha Reforming Process,Multifunctional Reactor,Palladium Membrane,Methaxylene Hydrodealkylation Process,Aromatic Production}, title_fa = {مدل‌سازی و شبیه‌سازی راکتورهای پیشنهادی چندمنظوره برای بهبود تولید آروماتیک‌ها در فرایند تبدیل کاتالیستی نفتا}, abstract_fa = {چکیده در این پژوهش بهبود فرایند تبدیل کاتالیستی نفتا به عنوان یکی از فرایندهای مهم در پالایشگاه‌ها و پتروشیمی‌ها مورد توجه قرار گرفته است. تمرکز اصلی بر روی تعویض راکتورهای معمولی بستر پرشده فرایند با راکتورهای جدید چندمنظوره است. این راکتورهای پیشنهادی شامل فرایندهای تبدیل کاتالیستی نفتا و هیدرودی‌آلکیلاسیون متازایلن است که توسط دیواره جامد از هم جدا شده‌اند و قسمت گاز جارو کننده که توسط یک لایه غشای پالادیوم-نقره از قسمت تبدیل کاتالیستی جدا شده است. فرایند گرماگیر کاتالیستی از یک طرف با فرایند هیدرودی‌آلکیلاسیون متازایلن تبادل گرما می‌کند، در حالی که از طرف دیگر با قسمت گاز جارو کننده تبادل هیدروژن را انجام می‌دهد. با توجه به نتایج شبیه سازی، تولید مولی آروماتیک در سیستم پیشنهادی نسبت به راکتورهای معمولی حدود 11% افزایش ‌یافت. در نهایت تاثیرات شرایط عملیاتی مانند دمای خوراک فرایند هیدرودی‌آلکیلاسیون و فشار ورودی گاز جاروکننده بر روی عملکرد سیستم مورد مطالعه قرار گرفته است.}, keywords_fa = {فرایند تبدیل کاتالیستی نفتا,راکتور چندمنظوره,غشای پالادیومی,فرایند هیدرودی‌آلکیلاسیون متازایلن,تولید آروماتیک}, url = {https://jsse.uk.ac.ir/article_2600.html}, eprint = {https://jsse.uk.ac.ir/article_2600_b254acecd87d31f0ed6e9dd9e878d3f4.pdf} } @article { author = {Valizadeh, Solmaz and Naji, Leila and Karimi, Mohammad}, title = {Systematic investigation of effective parameters on formation and performance of graphene oxide separation thin film membranes}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {29-40}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2601}, abstract = {Recently-developed graphene oxide (GO) thin film membranes have attracted a great deal of attention in water-treatment processes because of their high water flux and low preparation costs. In the present work, the parameters influencing the physicochemical and the separation performance of the GO thin film membranes has been introduced and the prepared membranes were applied to separate Rhodamine-B (RhB) from aqueous solutions. The effects of various parameters including GO oxidation degree, type of polymeric support, the method of membrane preparation, surface modification of the support and the concentration of GO solution on the properties of the resulting membranes were investigated. The best GO membrane, in terms of physical properties and the separation performance, was achieved by pressure-assisted filtration of GO containing higher level of oxygenated groups on the polyethersulfone (PES) support. The physical properties of this membrane was further improved through surface modification of PES by dopamine prior to the deposition of GO thin film membrane. The best GO concentration was found to be about 50 ppm. The membrane prepared in the optimized conditions removed about 94 % of RhB from water, while its pure water flux was about 623 L.M-2.h-1.}, keywords = {"Graphene oxide","Membrane Separation","Polyethersulfone","Polydopamine","Thin film membrane"}, title_fa = {ارزیابی سیستماتیک اثر پارامترهای موثر بر تشکیل و عملکرد غشاهای جداسازی لایه نازک اکسیدگرافن}, abstract_fa = {غشاهای بر پایه‌ی اکسیدگرافن (GO) غشاهای نوظهوری در فرایندهای جداسازی می‌باشند که به دلیل دبی آب بسیار بالاو هزینه‌ی تولید پایین، در فرایندهای تصفیه آب مورد توجه قرار گرفته‌اند. در کار حاضر پارامترهای موثر در خواص فیزیکی، شیمیایی و عملکرد غشاهای لایه نازک GO در جداسازی ماده رنگزای آلی ردامین-بی (Rh-B) از آب بررسی شد. برای حصول غشای بهینه، اثر درجه اکسایش GO، جنس ساپورت پلیمری، نوع فرایند غشاگیری، اصلاح سطح ساپورت و غلظت محلول GO مورد استفاده برای تهیه غشا بررسی شد. غشای بهینه از لحاظ خصوصیات فیزیکی و عملکرد جداسازی، برای GO با درجه اکسایش بالاتر با استفاده از ساپورت پلی‌اترسولفون (PES) و روش خودآرایی تحت فشار بدست آمد. همچنین اصلاح سطح با استفاده از دوپامین موجب بهبود خواص فیزیکی غشا گردید. غلظت بهینه محلول GO برای کنترل ضخامت و عملکرد غشا ppm50 حاصل شد. در نهایت غشای بهینه تهیه شده میزان حذف 94 % را برای Rh-B از آب و میزان دبی آب خالص L.m-2h-1 623 را نشان داد.}, keywords_fa = {"اکسیدگرافن","جداسازی غشایی","پلی اترسولفون","پلی دوپامین","غشای لایه نازک"}, url = {https://jsse.uk.ac.ir/article_2601.html}, eprint = {https://jsse.uk.ac.ir/article_2601_591832d2f2fd6b6349f600aa46149a6d.pdf} } @article { author = {Najminoori, Mahjabin and محبی, علی and Sadeghi, Roohollah and Afrooz, Kambiz and Ghadamiarabi, Babak}, title = {CFD Study of Magnetic Field Effect on the Performance of Copper Electrodeposition Cells}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {41-66}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2627}, abstract = {In copper electrodeposition methods, by applying an electric current between two electrodes immersed in an electrolyte containing CuSO4- H2SO4-H2O, copper is deposited on the cathode surface. Presence of magnetic field has a considerable effect on the performance of electrodeposition cells. The most important roles of the magnetic field on these processes are Lorentz force, magnetohydrodynamic (MHD) convection and its interaction with the natural convection induced by the concentration gradient. In this study, an unsteady, two-dimensional copper electrolysis (one phase) and electrowinning (two-phase liquid-gas) cells were simulated in the presence of magnetic field by using Computational Fluid Dynamics (CFD). The equations of Nernst-Planck, momentum and electric potential were solved by finite volume method. The Eulerian-Lagrangian method was used in simulation of two-phase copper electrowinning cell. The simulation results of electrolysis process showed a good agreement in comparison with experimental data of Muhlenhoff et al. After the validation of the model, copper concentration change and velocity profiles of two processes were investigated and compared with each other. The simulation results showed that the MHD interaction with the natural convection and also intrusion layer pile up leads to the velocity decay. As a result, the velocity reduction in the electrowinning process occurs later than in the electrolysis process but its reduction in the second stage of electrowinning process is about 93%, which is much more than 33% in the electrolysis process.}, keywords = {Copper electrodeposition,Magnetic field,Computational fluid dynamics,MHD convection,Natural convection}, title_fa = {مطالعه اثر میدان مغناطیسی بر عملکرد سلول های رسوبگیری الکتروشیمیایی مس به کمک دینامیک سیالات محاسباتی}, abstract_fa = {در روش‌های رسوبگیری الکتروشیمیایی مس، با اعمال جریان الکتریکی بین دو الکترود غوطه ور در الکترولیت شامل CuSO4-H2SO4-H2O، مس روی سطح الکترود کاتد رسوب می‌کند. حضور میدان مغناطیسی تاثیر قابل توجهی بر عملکرد سل‌های رسوبگیری الکتروشیمیایی دارد. مهمترین نقش‌های میدان مغناطیسی در این فرآیند‌ها نیروی لورنتز، جا‌به‌جایی هیدرودینامیک مغناطیسی (MHD convection) و اثر متقابل آن با جا‌به‌جایی طبیعی ناشی از گرادیان غلظت هستند. در این مطالعه به کمک دینامیک سیالات محاسباتی (CFD)، شبیه‌سازی دو بعدی و ناپایدار سل‌های الکترولیز (تک فازی) و الکترووینینگ (دو فازی (مایع-گاز)) مس در حضور میدان مغناطیسی انجام شد. معادلات انتقال جرم ذرات نرنست- پلانک، مومنتوم و پتانسیل الکتریکی به کمک روش حجم محدود حل شده‌اند. در شبیه‌سازی دو فازی سل الکترووینینگ مس روش اولرین-لاگرانژین برای الکترولیت و گاز اکسیژن به کار برده شد. نتایج شبیه‌سازی فرآیند الکترولیز تطابق خوبی با داده‌های آزمایشگاهی ارائه شده توسط مولنهاف و همکارانش داشت. پس از اعتبار‌سنجی مدل، تغییرات غلظت مس و سرعت الکترولیت دو فرآیند مطالعه و با هم مقایسه شد. نتایج شبیه‌سازی نشان داد که اثر متقابل بین جا-به‌جایی MHD و جا‌به‌جایی طبیعی و همچنین انباشته شدن لایه‌های غلظتی باعث کاهش سرعت الکترولیت می‌شود. در نتیجه کاهش سرعت در فرآیند الکترووینینگ دیرتر از فرآیند الکترولیز اتفاق می‌افتد، اما کاهش سرعت الکترولیت در مرحله‌ی دوم فرآیند الکترووینینگ مس حدود % 93 و خیلی بیشتر از کاهش % 33 در فرآیند الکترولیز مس است.}, keywords_fa = {رسوبگیری الکتریکی مس,میدان مغناطیسی,دینامیک سیالات محاسباتی,جابه جایی هیدرودینامیک مغناطیسی,جابه جایی طبیعی}, url = {https://jsse.uk.ac.ir/article_2627.html}, eprint = {https://jsse.uk.ac.ir/article_2627_371a3598ea300970d8ddfe7d9d1e29bb.pdf} } @article { author = {Estarabadi, Majid and Omidvar, Maryam and Koohestanian, Esmaeil and Hejri, Zahra}, title = {Preparation and characterization of modified poly (ethersulfone)/hematite iron oxide nano particles (α-Fe2O3) ultrafiltration membranes: food industrial wastewater treatment}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {67-78}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2631}, abstract = {In this research, new polyethersulfone ultrafiltration membranes was prepared via phase inversion technique. polyethersulfone was used as a polymer, hematite iron oxide nanoparticles (α-Fe2O3) as an additive, polyvinylpyrrolidone as a pore former, 1-methyl-2-pyrrolidone as a solvent, in preparation of the casting solutions and the distillated water as a gelation media. The effect of nanoparticles concentration (0, 0.25, 0.75 and 1 wt. %) was studied on the membrane characteristics, including membrane morphology, contact angle, pure water flux and the food industrial wastewater treatment using the scanning electron microscopy, water contact angle apparatus and experimental set-up. According to the results, increasing the concentration of the iron oxide nanoparticles from 0 to 0.75 wt. % led to the improved membranes with a higher thickness, a more porous structure in the sublayer, and a higher hydrophilicity and pure water flux. As the results showed, in the membrane containing 0.75 wt% hematite iron oxide nanoparticles, the contact angel decreased from 65.79 ± 2.36 to 35.19 ± 1.38 and pure water flux increased from 33.09 l/m2h to 53.98 l/m2h at pressure of 5 bar. The membrane performed well in rejecting the wastewater contaminants.}, keywords = {Polyethersulfone membrane,hematite iron oxide nanoparticles,waste water treatment}, title_fa = {ساخت و ارزیابی غشاهای جدید اولترافیلتراسیون پلی اترسولفون/نانوذرات اکسیدآهن هماتیت (α-Fe2O3) : تصفیه پساب صنایع غذایی}, abstract_fa = {در این تحقیق، غشاهای اولترا فیلتراسیون پلی اترسولفون جدید به وسیله روش وارونگی فاز تهیه شد. از پلی اتر سولفون بعنوان پلیمر، نانوذرات اکسید آهن هماتیت بعنوان افزودنی، پلی وینیل پیرولیدون بعنوان شکل دهنده حفرات و 1- ان متیل -2- پیرولیدون بعنوان حلال در تهیه محلول‌های ریخته‌گری ساخت غشاها و همچنین از آب مقطر بعنوان محیط انعقاد استفاده شد. تاثیر غلظت نانوذرات اکسیدآهن (%25/0، %5/0، %75/0و %1 وزنی) بر روی خصوصیات غشا شامل مورفولوژی، زاویه‌ی تماس، شار آب خالص و تصفیه پساب صنایع غذایی بوسیله میکروسکوپ الکترونی روبشی، دستگاه اندازه‌گیری زاویه تماس و پایلوت آزمایشگاهی بررسی شد. طبق نتایج بدست آمده، افزایش غلظت نانوذرات اکسیدآهن از 0 تا %75/0 وزنی به محلول ریخته‌گری منجر به ساخت غشاهایی بهبودیافته با ضخامت بیشتر، ساختاری حفره‌دارتر در لایه زیرین، آبدوستی و شار آب خالص بیشتر می‌گردد. همانطور که نتایج نشان داد در غشای حاوی % 75/ 0وزنی نانوذرات اکسیدآهن هماتیت، زاویه تماس از 36/2± 79/65 به 38/1± 19/35 درجه کاهش و شار آب خالص در فشار 5 بار از l/m2h09/33 به l/m2h 98/53 افزایش یافت. این غشا عملکرد بسیار خوبی در دفع آلاینده‌های پساب از خود نشان داد.}, keywords_fa = {غشا پلی اتر سولفون,نانوذرات اکسید آهن هماتیت,تصفیه پساب}, url = {https://jsse.uk.ac.ir/article_2631.html}, eprint = {https://jsse.uk.ac.ir/article_2631_ee64f9399500dc79b7565203a9a6b8a4.pdf} } @article { author = {Feili Monfared, Amir Ehsan and Sarrafi, Amir}, title = {Modeling and Design of Rotating Packed Beds by the employment of Artificial Intelligence Methods}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {79-96}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2643}, abstract = {In recent years, the capabilities of rotating packed beds in dust removal from gases has attracted the attention in different industries. On the other hand, due to intricate complexities of such beds, employment of computational fluid dynamic techniques for design and modeling purposes would be difficult. Therefore, in this research the performance of artificial intelligence techniques in design of theses equipment was investigated. Accordingly, in the first step and by using 561 experimental data points, an artificial neural network system was developed. In the constructed model, dust removal efficiency was considered as the output and the working and design conditions of the bed were fed as the inputs. Performance of the developed system was analyzed both quantitatively and qualitatively and achieving value of 0.99 for correlation coefficient demonstrates its suitable accuracy in efficiency determination. Finally, employing the developed neural network system combined with genetic algorithms, a novel method for optimum design of beds with arbitrary characteristics was proposed. Performed analyses showed that the constructed system while being simple, offers flexibility and precision in design of rotating packed beds. Also, its low coast of development makes it an attractive idea to be employed in industry scale.}, keywords = {Dust removal,Rotating packed bed,Efficiency,artificial neural networks,Genetic Algorithms}, title_fa = {مدل‌سازی و طراحی بسترهای آکنده دوار با استفاده از روش‌های هوش مصنوعی}, abstract_fa = {در سال‌های اخیر توانایی بسترهای آکنده دوار در غبارزادیی از گازها مورد توجه صنایع مختلف قرار گرفته است. از سوی دیگر به دلیل پیچیدگی‌های فراوان اینگونه بسترها، به‌کارگیری دینامیک سیالات محاسباتی در طراحی و مدل‌سازی آنها بسیار دشوار خواهد بود. از همین رو در پژوهش حاضر، عملکرد روش‌های هوش مصنوعی در طراحی این تجهیزات مورد بررسی قرار گرفت. بر این اساس، ابتدا با بکارگیری ۵۶۱ داده تجربی، سامانه‌ای مبتنی بر شبکه‌های عصبی مصنوعی توسعه داده شد. در این سامانه ویژگی‌های طراحی و شرایط کاری بستر بعنوان ورودی، و بازدهی بستر بعنوان خروجی مدل در نظر گرفته شد. عملکرد سامانه نیز مورد ارزیابی کیفی و کمی قرار گرفت و دستیابی به ضریب همبستگی ۹۹/۰ دقت مناسب آنرا در تخمین بازدهی نشان می‌دهد. در نهایت با استفاده از مدل آموزش داده شده در گام نخست و بکارگیری الگوریتم ژنتیک، روش نوینی جهت طراحی بهینه این بسترها با ویژگی‌های دلخواه و بازدهی مطلوب ارائه گردید. بررسی‌های صورت گرفته نشان داد که سامانه مذکور در عین سادگی، از دقت و انعطاف بالایی در طراحی بسترها برخوردار بوده و هزینه اندک توسعه، این روش را به ایده‌ای جذاب جهت بکارگیری در صنایع مبدل می‌کند.}, keywords_fa = {غبار زدایی,بستر آکنده دوار,بازدهی,شبکه عصبی,الگوریتم ژنتیک}, url = {https://jsse.uk.ac.ir/article_2643.html}, eprint = {https://jsse.uk.ac.ir/article_2643_b36f8999e5f23d39780eaf0750628bf5.pdf} } @article { author = {Yousefi, Mohammad and Azizi, shima and Peyghambarzadeh, S.M. and Azizi, Zoha}, title = {Experimental and Thermo-kinetic Study of Ethane Absorption in N-methyl-2-pyrrolidone Solvent}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {97-113}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2644}, abstract = {Determining the solubility of gases in solvents and considering non-ideality at different operating conditions are essential to design a cost-effective and energy-efficient absorption process. In this study, using a pressure decaying set-up, the solubility of pure ethane in N-methyl-2-pyrrolidone (NMP) was measured at different temperatures (278.15, 298.15, and 328.15 K) and pressures up to 14 bar, and kinetic and equilibrium results were obtained. Accordingly, the values of Henry’s law constants and also the heat of absorption were calculated at various temperatures. Then, thermodynamic modeling was accomplished by applying the Peng Robinson equation of state (PR-EOS) and the Wilson activity coefficient model, and the binary interaction parameters for this system were estimated. By the thermodynamic modeling, positive deviation from ideal behavior is apparently observed for this system. Due to low absolute average deviation of less than 12.3%, the correlated thermodynamic model is able to predict the ethane solubility in NMP with a reliable accuracy.}, keywords = {Solubility,Ethane,N-methyl-2-pyrrolidone,Absorption,Peng Robinson}, title_fa = {مطالعه آزمایشگاهی و ترموسینتیکی جذب گاز اتان در حلال نرمال متیل پیرولیدون}, abstract_fa = {ارزیابی حلالیت گازها در حلال‌های مختلف و بررسی غیرایده‌ال بودن در شرایط عملیاتی مختلف برای طراحی یک فرایند جذب اقتصادی و با مصرف کم انرژی ضروری می‌باشد. در این مطالعه، با استفاده از یک سامانه آزمایشگاهی به روش کاهش فشار، حلالیت گاز اتان خالص در حلال نرمال متیل پیرولیدون (NMP) در دماهای مختلف (15/278، 15/298 و 15/328 کلوین) و فشار تا 14 بار بررسی شد و نتایج سینتیکی و تعادلی به دست آمد. در نتیجه، مقادیر ثابت‌های قانون هنری و همچنین گرمای جذب در دماهای مختلف محاسبه شد. سپس، با استفاده از معادله حالت پنگ رابینسون (PR-EOS) و مدل ضریب فعالیت ویلسون، پارامترهای برهمکنش دو تایی این سیستم تخمین زده شد. با مدل‌سازی ترمودینامیکی، انحراف مثبت از حالت ایده‌ال در مورد این سیستم به وضوح مشاهده شد. به دلیل انحراف متوسط مطلق کمتر از 3/12 درصد، مدل ترمودینامیکی حاصل می‌تواند حلالیت اتان در نرمال متیل پیرولیدون را با دقت قابل اعتمادی پیش‌بینی نماید.}, keywords_fa = {حلالیت,اتان,نرمال متیل پیرولیدون,جذب,پنگ رابینسون}, url = {https://jsse.uk.ac.ir/article_2644.html}, eprint = {https://jsse.uk.ac.ir/article_2644_050be0d61704dd77a096d718e08687f9.pdf} } @article { author = {Naghavi, Hadi and دهقانی, علی and Karimi, Mohsen}, title = {Evaluation of Pyke model in Denver laboratory flotation cell for predicting pyrite flotation rate constants at different impeller speeds and particle sizes}, journal = {Journal of Separation Science and Engineering}, volume = {12}, number = {1}, pages = {114-125}, year = {2020}, publisher = {Shahid Bahonar University of Kerman Iranian Association of Chemical Engineering}, issn = {2008-3963}, eissn = {}, doi = {10.22103/jsse.2020.2656}, abstract = {The Pyke model is one of the fundamental models developed to predict the flotation rate constant. The model incorporates the effect of turbulence and hydrodynamic properties in the response of flotation sub-processes. The model has been evaluated in Rushton turbine flotation cells, which are induced-air flotation cells. The Denver self-aerated flotation cell is the most commonly used laboratory cell. The cell has fundamental differences in its aeration mechanism with a Rushton turbine tank aeration system. In this research, an attempt was made to investigate the performance of the Pyke model in predicting the flotation rate constant of pyrite from iron ore concentrate at different particle size ranges and impeller speeds. The experimental results showed that the flotation rate constants of intermediate and coarse particles were in the range of 1.1-2.1 and 0.8-1.1 s-1, respectively. In contrast, the fine particles had the lowest flotation rate constant in the range of 0.4-1.4 s-1. Besides, it was found that the flotation rate constants calculated using Pyke model are very similar to that of experiments for the coarse and intermediate particle sizes at different impeller speeds. However, for fine particles, the relative error between the measured and predicted values was greater than 4%. Some sources of error and limitations of the Pyke model are also discussed.}, keywords = {flotation,Flotation rate constant,Pyke Model,Particle size rang}, title_fa = {ارزیابی کارایی مدل پایک در سلول آزمایشگاهی دنور جهت پیش‌بینی ثابت نرخ شناوری پیریت در سرعت‌های مختلف همزن و اندازه متفاوت ذرات}, abstract_fa = {یکی از مدل‌های بنیادی توسعه داده شده برای پیش‌بینی ثابت نرخ شناوری فلوتاسیون، مدل پایک است که تاثیر اغتشاش سیستم و خصوصیات هیدرودینامیکی را بر زیرفرآیندهای فلوتاسیون در نظر می‌گیرد. کارایی این مدل تاکنون در سلول‌های توربینی راشتون که از نوع سلول‌های فلوتاسیون هوادهی شده هستند، ارزیابی شده است. سلول خودهواده دنور، رایج‌ترین سلول استفاده شده آزمایشگاهی است و تفاوت‌های اساسی در مکانیزم هوادهی، هندسه سلول و همزن با سلول توربینی راشتون دارد. در این تحقیق تلاش شد تا کارایی مدل پایک در پیش‌بینی ثابت نرخ شناوری ذرات پیریت از کنسانتره سنگ‌آهن در دامنه‌های مختلف ابعادی ذرات و سرعت‌های مختلف همزن در این نوع سلول بررسی شود. نتایج تجربی به دست آمده نشان داد که با توجه به سرعت همزن، ثابت نرخ شناوری ذرات با ابعاد میانی و درشت به ترتیب در محدوده s-1 4/۱-۲/۱ و s-1 ۱/۸-1/0 بودند در حالی که ذرات ریز‌دانه کمترین ثابت نرخ شناوری را در محدوده s-1 4/4-1/0 داشتند. علاوه بر این مشخص شد که ثابت‌های نرخ شناوری پیش‌بینی شده به وسیله مدل پایک با مقادیر تجربی به دست آمده در محدوده ابعادی درشت و متوسط از ذرات در سرعت‌های مختلف همزن، تطابق و همگرایی خوبی داشتند. اما در محدوده ابعادی ریزدانه و در هر سرعتی از همزن، خطای نسبی بین مقادیر اندازه‌گیری و پیش‌بینی شده ثابت نرخ شناوری ذرات بالاتر از 4% بود. برخی از منشاءهای خطا و محدودیت‌های مدل پایک در این مقاله بحث شده است.}, keywords_fa = {فلوتاسیون,ثابت نرخ شناوری,مدل پایک,دامنه دانه بندی ذرات}, url = {https://jsse.uk.ac.ir/article_2656.html}, eprint = {https://jsse.uk.ac.ir/article_2656_d764947f262316d768e38bed4b23240e.pdf} }